[email protected]

15-5 PH - Rolled Alloys, Inc.

15-5 PH. The 15-5 PH alloy was designed to have greater toughness than 17-4 PH. The 15-5 PH alloy is martensitic in structure in the annealed condition and is further strengthened by a relatively low temperature heat treatment which precipitates a copper containing phase in the alloy. 15-5 PH is also referred to as XM-12 in some specifications. Blade Steels, Steel Analysis and Heat Treating Methods Hardening. It is advisable to protect steel with some inert material packed in containers or to heat in a well-regulated atmosphere-controlled furnace to prevent decarburization. Preheat at 1200 and soak. Then heat to 1750 - 1800 and hold for 1 hr per inch of greatest thickness.

Bolt Depot - USS SAE Washer Dimensions

USS and SAE Washer Dimensions. Print this page . Size USS SAE; Inside Diameter (A) Outside Diameter (B) Thickness CHATHAMSTEELCORPORATION 25 HOT ROLLED BLACK HOT ROLLED BLACK SHEETS. COMMERCIALQUALITYA-569. Size(In.) Nom.Thickness WeightPerSheet 7GA x48 x96 (.1793) 240.0(Lbs.) x48 x120 300.0 x48 x144 360.0 x48 x240 600.0 x60 x120 375.0 x60 x240 750.0 x72 x120 450.0 x72 x144 540.0 x72 x240 900.0 10GA x48 x96 (.1345) 180.0(Lbs.) x48 x120 225.0 x48 x144 270.0 x60 x120 281.3 x72 x120 337.5 x72 x144 405.0 11GA Datasheet for Steel Grades Carbon Steel AISI 1020HRC 30 - AISI 1020 Heat Treatment Regime Annealing Quenching Tempering Normalizing Q & T AISI 1020 Range of products Product type Products Dimension Processes Deliver Status Plates / Sheets Plates / Sheets 0.08-200mm(T)*W*L Forging, hot rolling and cold rolling Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting

High Speed Steel H13 Steel H13 H13 Technical Data

  • ApplicationsProductsPreparationCharacteristicsHeat at a rate not exceeding 400°F per hour (222°C per hour) to 1575-1625°F (857-885°C), and hold at temperature for 1 hour per inch of maximum thickness; 2 hours minimum. Then cool slowly with the furnace at a rate not exceeding 50°F per hour (28°C per hour) to 1000°F (538°C). Continue cooling to ambient temperature in the furnace or in air. The resultant hardness should be a maximum of235 HBS.Sheet Metal Gauge Thickness Chart (to mm/inch Conversions Ga. is different from inches, there is no conversion formula. Even when the non-ferrous metal plate and the steel plate are the same Ga., the thickness is actually different. You can find the gauge to mm / inch conversion for sheet metal by the chart below. Hot Rolled Coils - HR Coil Latest Price, Manufacturers Hot Rolled Coils. 44,500/ Ton Get Latest Price. Brand:Ferrite Structural Steels Private Limited. Thickness mm:Width mm. 0.27, 0.30, 0.35:900, 905, 910, 914, 920. 0.40, 0.45:900, 905, 910, 914, 920, 1000, 1005, 1010, 1020. 0.5:900, 905, 910, 914, 920, 1000, 1005, 1010, 1020, read more SAE AISI 1080 Steel Properties Heat Treatment Composition Hot rolled:19-31.8 (0.75-1.25 in.) 675 (98) (50 °F/h) in the furnace at the full annealing temperature range. (For section thickness 75 mm, full annealing temperature is 1 hour at least for thickness 25.4 mm, 0.5 hour is added for each additional 25.4 mm thickness) The Rockwell C hardness after quenching is about 65 HRC. The

    SAE AISI 4340 Steel Properties, Heat Treatment, Equivalent

    Hardening:Heat to 800 to 845 °C (1475 to 1550 °F) for 15 minutes (minimum 15 minutes) per 25 mm (1 inch) thickness; oil quench to below 65 °C (150 °F), or quench in fused salt at 200 to 210 °C (390 to 410 °F), hold for 10 minutes, and then air-cool to below 65 °C (150 °F). Steel Dynamics, Inc. - Flat RollAfter hot-rolled sheet is pickled, leveled, and edge-trimmed, our cold-rolling mill is capable of reducing the steels thickness to as thin as 0.013 inches and as thick as .085 inches. Coated steel sheet. We galvanize hot-roll and cold-roll steel sheet, offering galvanneal, Aluminized Type 1 and Galvalume®, as well as acrylic overcoat options. Painted steel sheet. We also pre-paint coils with thickness ranging from .012 inches to .071 inches and width ranging from 36 inches to 61.5 inches Hot Rolled Steel - Hot Rolled Steel Sheet & Coil Steel Hot-Rolled steel has been rolled at high temperature from a cast steel slab more than two inches thick into steel coil as thin as 1/16 of an inch thick. Because the steel is rolled hot, and the reduction from slab to coil is great, the coil surfaces are noticeably rough and slightly oxidized. It is recommended for precision thickness Hot Rolled Strip and high formability.