[email protected]

(PDF) Notes on Design Of Steel Parking Structures

Structural Steel Educational Council or of any other person named herein, that this Epoxy polyamide zinc-rich primer SSPC-Paint 20, Type II. Request paint supplier to preliminary ARCHITECTURALLY EXPOSED STRUCTURAL STEELType 1, round-head assemblies, consisting of steel structural bolts with splined ends, heavy-hex carbon-steel nuts, and hardened carbon-steel washers. 1. Finish:Mechanically deposited zinc coating. 2.2 PRIMER A. Primer:Comply with Section 09900 Painting Etching Cleaner for Galvanized Metal:Complying with MPI#25.

Current Active Standards

SSPC-Paint 23 Latex Primer for Steel Surfaces March 2013 SSPC-Paint 24 :Latex Exterior Finish Coat for Steel Surfaces, Performance-Based October 2016 . SSPC-Paint 27 Basic Zinc Chromate-Vinyl Butyral Wash Primer November 2004 SSPC-Paint 29 Zinc Dust Sacrificial Primer, Performance February 2014 SSPC-Paint 30 :Weld Through IOZ primer Paint and Coatings Industry Standards from SSPC :SSPC-PS SSPC-PS Guide 7.00, Guide for Selecting One-Coat Shop Painting Systems: They can be used on open frames or structural steel in buildings not subjected to high humidity, condensation, or corrosive fumes. The paints covered by this guide are primers, and if a color other than the standard color is required, then the color must be specified. Properly Prepared - American Institute of Steel Steel that is to be painted must be prepared to a minimum of SSPC-SP2 (Hand Tool Cleaning). The COSP addresses AESS in Section 10. This section notes that weathering steel must be pre-pared to category SSPC-SP6 (Commercial Blast Cleaning). This is done to remove scale that pre-vents the material from generating the even patina

Protective STEEL-SPEC EPOXY INTERMEDIATE

SSPC-SP1. Minimum surface preparation is Commercial Blast Cleaning per SSPC-SP6/NACE 3. For better performance, use Near White Metal Blast Cleaning per SSPC-SP10/NACE 2. Blast clean all surfaces using a sharp, angular abrasive for optimum surface pro le (2 mils). Prime any bare steel the same day as it is cleaned. Galvanized Steel S 8.12014, Guide Spec. for Application of Coating Introduction This Guide Specification represents a consensus on best industry practice for shop application of zinc rich coating systems to previously uncoated bridge steel and includes the proper preparation of the steel. To simplify the application parameters for a system based on zinc-rich primers on new steel bridges, a SSPC-SP 6 Commercial Blast Cleaning (NACE No. 3)SSPC-SP 6/NACE No. 3 commercial blast cleaning allows for stains or shadows up to 33 percent of each unit area of surface to remain. SSPC-SP 6/NACE No. 3 removes all visible oil, grease, dust, dirt, mill scale, rust, coating, oxides, corrosion products, and any other foreign matter on the surface.

STRUCTURAL STEEL COATINGS - Construction

Sumter Coatingsproducts are tested to ASTM, SSPC and Government TTP and DOD coating specifications for the structural steel industry. Sumter Coatingstechnical sales representatives in your area offer assistance on application and technical issues. COMPANY INTRODUCTION 7132_02 11/8/07 11:14 AM Page 2 Steel Primer and Surface PreparationSep 22, 2017 · The SSPC Surface Preparation Standards continue from SP-7 to SSPC-SP14. These are specific to coating systems that are not often used in construction based Structural and Miscellaneous steel fabricating. When steel is required to be coated using these surface preparations fabricators will often refer that portion of the job to an SSPC Contactor. Surface Preparation - Sherwin-WilliamsSolvent clean per SSPC-SP1, then prime as required. When weathering is not possible or the surface has been treated with chromates or silicates, first Solvent Clean per SSPC-SP1 and apply a test area, priming as required. Allow the coating to dry at least one week before testing.

Technical Guide Guide to Protective Coatings, Inspection

Step 1:Determine the number of spot measurements required on an area basis. Surface area of structure:26 feet x 10 feet = 260 square feet. Surface area is less than 300 square feet; therefore, 5 spot measurements are required in each of two 100 square [DOC]SECTION 09900 · Web view4. Existing Structural Steel, Metal Decks and Stairs:a. Prepare existing steel to be painted by cleaning in accordance with Structural Steel Painting Council (SSPC) standards:SELECT ONE OF THE FOLLOWING SUBPARAGRAPHS BELOW, DEPENDING UPON THE STEEL SUBSTRATE CONDITION AND AMOUNT OF CLEANING REQUIRED FOR PAINT TYPE ESP OR ISP PRIMER SSPC:The Society for Protective Coatings Using SSPC Oct 01, 2014 · Coating Selection SSPC coating material standards contain requirements compatible coatings:a primer, an intermediate coat and a topcoat, Manufacturers usually design individual coatings to Dry interiors where structural steel is embedded in concrete, encased in masonry, or protected by membrane or non-